So, I bought these new headers on the internet. they have these threaded holes in them (pictured above) which my original did not have.
My original had a hole in it, that's why I needed a new one
but not threaded....Any ideas?
| ducatipaso.org http://ducatipaso.org/forum/ |
|
| threaded holes in my new headers? http://ducatipaso.org/forum/viewtopic.php?f=1&t=7054 |
Page 1 of 1 |
| Author: | Pablo The Squirrel [ Mon Mar 02, 2015 9:38 pm ] |
| Post subject: | threaded holes in my new headers? |
So, I bought these new headers on the internet. they have these threaded holes in them (pictured above) which my original did not have. My original had a hole in it, that's why I needed a new one but not threaded....Any ideas? |
|
| Author: | paso750 [ Mon Mar 02, 2015 10:26 pm ] |
| Post subject: | Re: threaded holes in my new headers? |
some headers had connections for a gas analyzer. The thread should be a R1/8 (conical). The old plugs were #000047113 (now 78010091A). Not sure if #78010071A is the same. |
|
| Author: | paso750 [ Tue Mar 03, 2015 5:32 pm ] | |||
| Post subject: | Re: threaded holes in my new headers? | |||
my header
|
||||
| Author: | Pablo The Squirrel [ Fri Mar 13, 2015 7:46 pm ] |
| Post subject: | Re: threaded holes in my new headers? |
thanks. conical thread huh... the things you learn... |
|
| Author: | Pablo The Squirrel [ Wed Mar 18, 2015 1:34 am ] |
| Post subject: | Re: threaded holes in my new headers? |
and thanks for the part number. The local dealer had them in stock. 
|
|
| Author: | paso750 [ Wed Mar 18, 2015 9:35 am ] |
| Post subject: | Re: threaded holes in my new headers? |
got the washers, too? Applying some anti-seize is recommended. |
|
| Author: | Pablo The Squirrel [ Sat Mar 28, 2015 10:11 am ] |
| Post subject: | Re: threaded holes in my new headers? |
| Author: | paso750 [ Sat Mar 28, 2015 10:48 am ] |
| Post subject: | Re: threaded holes in my new headers? |
use a copper washer |
|
| Author: | Pablo The Squirrel [ Sat Apr 11, 2015 9:43 pm ] |
| Post subject: | Re: threaded holes in my new headers? |
| Author: | paso750 [ Thu Apr 16, 2015 10:09 am ] |
| Post subject: | Re: threaded holes in my new headers? |
that should be ok, too. It should just be a washer that also can seal. |
|
| Author: | higgy [ Thu Apr 16, 2015 10:01 pm ] |
| Post subject: | Re: threaded holes in my new headers? |
aluminum will work and are readily available |
|
| Author: | Pablo The Squirrel [ Mon Apr 27, 2015 2:44 am ] |
| Post subject: | Re: threaded holes in my new headers? |
| Author: | paso750 [ Mon Apr 27, 2015 9:22 am ] |
| Post subject: | Re: threaded holes in my new headers? |
you want that bolt to sit airtight so you use a washer made out of a softer material than steel |
|
| Author: | Pablo The Squirrel [ Mon Apr 27, 2015 11:26 am ] |
| Post subject: | Re: threaded holes in my new headers? |
| Page 1 of 1 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|