IMG_11012018_202340.jpg [ 311.13 KiB | Viewed 16828 times ]
| ducatipaso.org http://ducatipaso.org/forum/ |
|
| Oil leaks 89 900 ss http://ducatipaso.org/forum/viewtopic.php?f=13&t=7723 |
Page 15 of 34 |
| Author: | HIGHWAY89 [ Thu Jan 11, 2018 12:26 pm ] |
| Post subject: | Re: Oil leaks 89 900 ss |
IMG_11012018_202340.jpg [ 311.13 KiB | Viewed 16828 times ] |
|
| Author: | paso750 [ Sun Jan 14, 2018 10:54 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
| Author: | HIGHWAY89 [ Sun Jan 14, 2018 11:16 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
Hi G, I think the blockage won't affect anything but the clutch pack I'm a little concerned with as the last drive plate protrudes a little from the clutch drum and is tight against the circlip, I bought the kit from Justin who is Protwin in Perth, I believe he was Brook Henry's understudy, I might chuck it on the trailer and give him a visit to clarify some, |
|
| Author: | HIGHWAY89 [ Sun Jan 14, 2018 2:09 pm ] |
| Post subject: | Re: Oil leaks 89 900 ss |
IMG_14012018_220105.jpg [ 380.91 KiB | Viewed 16792 times ] Now I'm really confused as I have just removed the new clutch set and measured the stack height compared to the set I am replacing and the new set is appx 2.5 mm lower than the old so I can't see why barnett set sits proud of clutch drum yet the old set not reaching the external edge of drum as in pic, |
|
| Author: | paso750 [ Sun Jan 14, 2018 3:50 pm ] |
| Post subject: | Re: Oil leaks 89 900 ss |
That really is odd and would only make some sense if the last Barnett steel disc was a warped one which according to the installation manual it isn't. You removed the red springs again? Just asking. That has nothing to do with the problem. |
|
| Author: | paso750 [ Sun Jan 14, 2018 4:15 pm ] | ||
| Post subject: | Re: Oil leaks 89 900 ss | ||
My suspicion might be correct since I found this file online. It's the same Barnett clutch number but with a different setup. This one has a curved disc. The number of discs is not the same as shown in the instructions you posted. Which one corresponds to what you have?
|
|||
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 6:08 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
Yes mate the instructions I posted are exactly what I have, I will try fitting the old set and see what happens there, thanks and I'll let you know the results |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 10:32 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
IMG_15012018_181843.jpg [ 326.25 KiB | Viewed 16765 times ] Before trying old set I will post a pic of the clutch nut and amount of thread showing on the shaft, maybe I have got something wrong and the clutch drum isn't sitting where it should, and I'll look back for that on my disassembly photos, I may have to go back a bit , take clutch nut back off, I broke my homemade clutch tool torquing her up and the lock washer is toast so mighty be such a bad idea anyway, cheers |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 10:36 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
I had set torquewrench to 180 or so but didnt quite get there when my shit welding gave up, maybe 150 I got |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 10:40 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
IMG_15012018_183729.jpg [ 419.48 KiB | Viewed 16764 times ] |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 10:43 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
I may need to find a reasonably priced tool on ebay or maybe I should have another crack at making one from the old set as the original was only one thin driveplate |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 11:20 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
IMG_15012018_191159.jpg [ 351.03 KiB | Viewed 16764 times ] I had a look at my dismantle pics and the thread length visible same as now so I'm guessing my parts sequence must be right, but now with the old clutch set , springs and control plate in place the outer driveplate sits exactly where the barnett unit was sitting, ie, proud of the clutch drum as in this pic |
|
| Author: | HIGHWAY89 [ Mon Jan 15, 2018 11:24 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
As you can see its in one of the last pics before i stripped it, the plate was not proud, maybe thats just how they are until its actually been charged up and used? |
|
| Author: | paso750 [ Mon Jan 15, 2018 11:31 am ] |
| Post subject: | Re: Oil leaks 89 900 ss |
this tool works fine https://www.ebay.com/itm/Ducati-Clutch- ... cw&vxp=mtr They sell similar ones on ebay Australia, too but there they cost a little bit more. |
|
| Author: | Mc tool [ Mon Jan 15, 2018 6:17 pm ] |
| Post subject: | Re: Oil leaks 89 900 ss |
Mine is similar DSC02829.JPG [ 99.32 KiB | Viewed 16754 times ] ...........'cept it didn't break 
|
|
| Page 15 of 34 | All times are UTC |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|