|
It is currently Wed May 15, 2024 2:29 am
|
View unanswered posts | View active topics
|
Page 1 of 1
|
[ 7 posts ] |
|
Author |
Message |
Jorian
|
Post subject: Rear sprocket mounting dimensions? Posted: Sat Nov 02, 2019 9:23 am |
|
Joined: Wed Sep 25, 2019 6:37 am Posts: 24 Location: Australia
model: 906 Paso
year: 1989
|
Can someone kindly confirm the inside diameter size of the rear sprocket? It's a 1989 model 906.
Also, the owner's manual says it has 41 teeth, but the parts book says 40. Is there a well accepted preference?
Thanks, Jorian
|
|
Top |
|
|
Derek
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Sat Nov 02, 2019 11:15 am |
|
|
paso grand pooh-bah |
|
Joined: Thu Nov 03, 2011 10:13 am Posts: 769 Location: Scotland
model: 907 I.E.
year: 1994
|
90mm according to JT sprockets :
_________________ 1994 907ie 2017 Supersport 939 2015 Scrambler Classic 1982 Pantah 500SL (now sold)
Scotland
|
|
Top |
|
|
Mc tool
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Sat Nov 02, 2019 5:55 pm |
|
|
paso grand pooh-bah |
|
Joined: Wed Dec 05, 2007 12:35 am Posts: 1793 Location: Newzealand
model: 906 Paso
year: 1990
|
These bikes are fairly tall geared and mine , at 100kph in 6th gear is stumbling along at to low revs,sometimes I used 5th gear. So maybe try the 41
_________________ I wish I was young again............Id be heaps smarter than last time
|
|
Top |
|
|
Jorian
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Sat Nov 02, 2019 10:44 pm |
|
Joined: Wed Sep 25, 2019 6:37 am Posts: 24 Location: Australia
model: 906 Paso
year: 1989
|
The one here has ID = 92mm, but it is evidently changed to suit an adaptor for use with a wide tyre which is no longer to be used. The sprocket carrier is also modified unfortunately, down to 88mm. Does anyone have a spare carrier they want to sell? Otherwise I'll have to restore this one, which I'd rather not.
Good also to have info on the ratios, so Thanks Folks.
|
|
Top |
|
|
Mc tool
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Sat Nov 02, 2019 11:57 pm |
|
|
paso grand pooh-bah |
|
Joined: Wed Dec 05, 2007 12:35 am Posts: 1793 Location: Newzealand
model: 906 Paso
year: 1990
|
You could get a ring turned up , to fit between sprocket and carrier .....if you did it right you could use a larger/modified washers under the sprocket nuts to hold it in place
_________________ I wish I was young again............Id be heaps smarter than last time
|
|
Top |
|
|
Jorian
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Wed Nov 06, 2019 9:41 pm |
|
Joined: Wed Sep 25, 2019 6:37 am Posts: 24 Location: Australia
model: 906 Paso
year: 1989
|
I found what I hope is the correct sprocket carrier, and bought it via ebay. It was not described as being fit for a Paso, but looks identical to the one here (modified).
|
|
Top |
|
|
Jorian
|
Post subject: Re: Rear sprocket mounting dimensions? Posted: Thu Dec 12, 2019 6:00 am |
|
Joined: Wed Sep 25, 2019 6:37 am Posts: 24 Location: Australia
model: 906 Paso
year: 1989
|
The received sprocket carrier is an assembly - light metal casting plus steel sleeve, spacers, bearings etc. The casting looks to be identical, and it's the internal parts that differ. Need to swap them for the Paso bits. I looked at some drawings of the bevel 900SS assembly, looks like I need to do some press work. Anyone done this, have any tips or warnings?
|
|
Top |
|
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 4 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|